Uncategorized

can t access router gui ubiquiti community

The Internet facilitates people’s lives. You can do almost anything online: manage your bank deposits, buy food, order air tickets, and so on. This means that the account is important to you. Set strong and different passwords for each service. If you have many accounts, then here is a suggestion: make use of a password manager.

unable to connect to Ubiquiti UniFi … – Spiceworks Community

https://community.spiceworks.com/topic/2274904…

Jun 12, 2020 · we currently have a Windows PC equipped with an ethernet connection and a WiFi connection. the ethernet connection is supplied a LAN IP address in the range 192.168.10.xxx while connected to a domain. the WiFi connection is supplied an IP address by our router in the range 192.168.100.xxx. this same PC is also running the Ubiquiti UniFi controller software …

EdgeRouter – How to Access the EdgeRouter – Ubiquiti …

https://help.ui.com/hc/en-us/articles/360001016814…
  • People also ask
    What kind of router do you use for Ubiquiti?

    What kind of router do you use for Ubiquiti?

    I use Ubiquiti’s Unifi Router (known as the “Unifi Security Gateway”) and a DrayTek Vigor 130 modem (both of which I highly recommend). The USG’s are very capable devices with impressive functionality. Problem was, there is no way to enable access to the modem in the GUI.

    Accessing a Modem’s Web Interface through a Ubiquiti USG …

    EdgeRouter – How to Configure an Interface – Ubiquiti …

    https://help.ui.com/hc/en-us/articles/204960104…

    GUI: Access the EdgeRouter Web UI. 1. On the workstation, open a Web Browser and enter https://192.168.1.1 in the address bar. 2. Log into the router using the default credentials. Username: ubnt. Password: ubnt. 3. Confirm that the device is running the latest firmware from our Downloads page.

    Edge router x, can’t access web gui + no internet. : Ubiquiti

    https://www.reddit.com/r/Ubiquiti/comments/hl4zkv/…

    I have edge router x connected to my isp supplied zyxel router, which is in bridge mode. I was able to set up edgerouter X yesterday evening, and everything was working. However this morning nothing worked. I’ve been unable to access the webgui via 192.168.1.1 since then. Webgui is accessible through ubiquiti discovery and rescue web gui, though.

    Accessing a Modem’s Web Interface through a Ubiquiti USG …

    https://owennelson.co.uk/accessing-a-modems-web…

    Aug 02, 2017 · Ubiquiti’s USG. The USG’s are very capable devices with impressive functionality. Problem was, there is no way to enable access to the …

    Site to site edgerouter, can’t access GUI on remote router …

    https://www.reddit.com/r/Ubiquiti/comments/5fwkvf/…

    MysticRyuujin. · 4y · edited 4y. Edit: Actually, I can see that you’re referring specifically to a Site-To-Site. My answer would only work over a the WAN… Try adding: set service gui https-port 443. Then try connecting to the internal IP of the EdgeRouter on the other side of the VPN (Not the WAN IP) 1. View Entire Discussion (2 Comments)

    Can’t ping Ubquiti EdgeRouter from … – Spiceworks Community

    https://community.spiceworks.com/topic/2139043-can

    Jun 01, 2018 · From a host connected to one of the switch ports on the router I can ping the 0/8 interface IP on the Switch, but cannot ping the host on VLAN10. From a host in VLAN10 I can ping the IP of interface 0/8, 10.64.251.2, but cannot ping the IP of …

    Solved: Unable to access Router Login with IP address. ‘Th …

    https://community.netgear.com/t5/Cable-Modems…

    May 23, 2016 · Use the procedure in this article ( link) do determine the address of your router and use that in case it’s not 192.168.1.1. You can also try entering http://routerlogin.net into your browser. Most Netgear routers will recognize this URL and connect the browser to the router login process. Message 3 of 12. 0 Kudos.

    I can’t access my router; what do I do? | Answer | NETGEAR …

    https://kb.netgear.com/27199

    Aug 09, 2021 · This article provides troubleshooting steps if you can’t access your router. Note: The easiest way to manage your router’s settings and wireless network is the Nighthawk app. You can use the Nighthawk app to update your router’s firmware or check the speed of your network. To check if your product is supported, see Which products support the NETGEAR

    Can’t Access GUI – Cisco Community

    https://community.cisco.com/t5/switching/can-t-access-gui/td-p/3927982

    Sep 21, 2019 · After I create a VLAN i can no longer access the GUI. port 1 – trunk connected to router. port 2 – access, PC. The switch is connected to an Edgerouter. I’m sure it’s something simple, but I’m new to VLANs and can’t figure it out.